Line Array Systems WideLine-10 Series
WideLine-10 WL2102

The 2 or 3-way line array system shall incorporate dual 10 inch cone transducers with 3 inch voice coils, and a 1.4-inch exit 3.0 inch titanium diaphgram compression driver with a neodymium magnet mounted to a multiple aperture diffraction waveguide. The low frequency drivers shall be loaded into a ported enclosure. The line array system shall have a passive internal crossover network with switchable bi-amp / tri-amp operation.

The line array system shall meet the following performance criteria: frequency response of 55 Hz to 18.0 kHz ±3 dB, measured on axis with recommended DSP; low frequency sensitivity of 98.0 dB SPL for a single enclosure in free field at 1 meter with an input of 2.83V and and the woofers connected in parallel, and high frequency sensitivity of 107.5 dB SPL; continuous low frequency output of 127 dB SPL and high frequency output of 127 dB SPL; peak low frequency output of 133 dB SPL and high frequency output of 133 dB SPL; low frequency (80 - 800 Hz) power handling of 600 watts for two hours using the AES1984-2 procedure in bi-amp mode or 400 watts (x2) in tri-amp mode; high frequency (1 to 10 kHz) power handling of 80 watts for two hours using the AES1984-2 test; recommended low frequency amplifier power of 1400 watts in bi-amp mode or 700 (x2) in tri-amp mode and recommended high frequency amplifier power of 300 watts; nominal low frequency impedance of 8 ohms in bi-amp mode or 16 ohms (x2) in tri-amp mode and nominal high frequency impedance of 16 ohms. The line array system's nominal horizontal nominal coverage between -6 dB points shall be 140 degrees; vertical coverage shall be dependent on the line array configuration.

The loudspeaker shall have a trapezoidal enclosure constructed of cored composite. It shall have a black finish. Input connectors shall be parallel wired Neutrik NL8 SpeakOns. The line array system shall have an integral side plate adjustable rigging system; vertical splay shall be adjustable in 1 degree increments from 0 to 10 degrees. The front of the line array system shall be protected by a perforated, formed powder coated steel grill.

The line array system's enclosure shall be 10.8 in (27.4 cm) high, 27.4 in (69.6 cm) wide and 20.75 in (52.7 cm) deep. The loudspeaker shall weigh no more than 70.0 lb (31.8 kg).

The 2 or 3-way line array system shall be the QSC Audio Products WideLine-10 WL2102.



Line Array Systems WideLine-10 Series
WideLine-10 WL2102-w

The 2 or 3-way line array system shall incorporate dual 10 inch cone transducers with 3 inch voice coils, and a 1.4-inch exit 3.0 inch titanium diaphgram compression driver with a neodymium magnet mounted to a multiple aperture diffraction waveguide. The low frequency drivers shall be loaded into a ported enclosure. The line array system shall have a passive internal crossover network with switchable bi-amp / tri-amp operation.

The line array system shall meet the following performance criteria: frequency response of 55 Hz to 18.0 kHz ±3 dB, measured on axis with recommended DSP; low frequency sensitivity of 98.0 dB SPL for a single enclosure in free field at 1 meter with an input of 2.83V and and the woofers connected in parallel, and high frequency sensitivity of 107.5 dB SPL; continuous low frequency output of 127 dB SPL and high frequency output of 127 dB SPL; peak low frequency output of 133 dB SPL and high frequency output of 133 dB SPL; low frequency (80 - 800 Hz) power handling of 600 watts for two hours using the AES1984-2 procedure in bi-amp mode or 400 watts (x2) in tri-amp mode; high frequency (1 to 10 kHz) power handling of 80 watts for two hours using the AES1984-2 test; recommended low frequency amplifier power of 1400 watts in bi-amp mode or 700 (x2) in tri-amp mode and recommended high frequency amplifier power of 300 watts; nominal low frequency impedance of 8 ohms in bi-amp mode or 16 ohms (x2) in tri-amp mode and nominal high frequency impedance of 16 ohms. The line array system's nominal horizontal nominal coverage between -6 dB points shall be 140 degrees; vertical coverage shall be dependent on the line array configuration.

The loudspeaker shall have a trapezoidal enclosure constructed of Baltic birch plywood. It shall have a black finish. Input connectors shall be parallel wired Neutrik NL8 SpeakOns. The line array system shall have an integral side plate adjustable rigging system; vertical splay shall be adjustable in 1 degree increments from 0 to 10 degrees. The front of the line array system shall be protected by a perforated, formed powder coated steel grill.

The line array system's enclosure shall be 10.8 in (27.4 cm) high, 27.4 in (69.6 cm) wide and 20.75 in (52.7 cm) deep. The loudspeaker shall weigh no more than 83.0 lb (37.7 kg).

The 2 or 3-way line array system shall be the QSC Audio Products WideLine-10 WL2102-w.